OEM/ODM Factory for Tube Cutter TC-01 to Singapore Importers
OEM/ODM Factory for Tube Cutter TC-01 to Singapore Importers Detail:
Easy to cut tubes.
Blade inside plastic housing
1-30mm tube size can be cutted easily.
Product detail pictures:
Related Product Guide:
Your Best Tools, Air Hoses
The History of Rubber Hoses
Our enterprise insists all along the standard policy of "product high-quality is base of business survival; client satisfaction could be the staring point and ending of an business; persistent improvement is eternal pursuit of staff" as well as consistent purpose of "reputation first, client first" for OEM/ODM Factory for Tube Cutter TC-01 to Singapore Importers, The product will supply to all over the world, such as: Ghana, Doha, Bogota, Satisfaction and good credit to every customer is our priority. We focus on every detail of order processing for customers till they have received safe and sound solutions with good logistics service and economical cost. Depending on this, our solutions are sold very well in the countries in Africa, the Mid-East and Southeast Asia.
For more information and resources, please visit http://go.3M.com/35kY
The 3M 1860 is a “cone” shaped particulate respirator and surgical mask. The 1860S is a smaller version of the 1860.
Follow these instructions each time you don your respirator in order to achieve a proper fit.
• Begin by cupping the respirator in your hand, holding the metal nosepiece at your fingertips. The straps should hang freely below your hand.
• Place the respirator under your chin with the nosepiece up. While holding the respirator in place, pull the top strap over your head with the opposite hand and position it high on the back of your head above your ears. While still holding the respirator firmly on your face, pull the bottom strap over your head and position it around your neck, below your ears. Make sure the straps are not twisted for increased comfort.
• Place the fingertips of both hands at the top of the metal nose strip and mold the nosepiece to the shape of your nose using both hands. Push inward while moving your fingertips down both sides of the nosepiece.
Always use two hands when molding the nosepiece. Pinching with one hand may result in improper fit and less effective respirator performance.
Perform the following User Seal Check each time the respirator is put on.
• Cup both hands over the respirator, covering it as much as possible and being careful not to disturb the position of the respirator.
• Inhale and exhale sharply. If air leaks around the nose, readjust the nosepiece for a more secure seal and repeat the user seal check.
• If air leaks around the respirator edges, adjust the position on the face and the straps along the sides of the head. Repeat the User Seal Check.
Do not enter a respiratory isolation or other hazardous area where respirators are required until you are assured you have a proper fit. If you have difficulty achieving a fit, review the respirator User Instructions located inside the packaging or refer to the instructions on the 3M 1860 “Wear it Right” poster to be sure that you are following the correct procedure.
If you are still unable to achieve a fit, see your supervisor or a representative from your infection control, employee health or safety department. Do not enter a hazardous or infectious area.
To properly remove the respirator:
• Do NOT touch the facepiece
• Slowly lift the bottom strap from around your neck up and over your head, while keeping the respirator seated against your face
• Lift off the top strap
• Carefully remove the respirator without allowing the outside of the respirator to come in contact with your body
• Perform hand hygiene
3M recommends you practice this removal procedure until you are proficient and comfortable with the procedure and before actual use of the respirator for the first time.
Leave the hazardous area immediately and replace the respirator if it is:
• Difficult to breathe through
• Contaminated with blood or body fluids
Follow your facility’s Infection Control Policies and Procedures for guidance on how frequently you should replace your respirator.
Follow the proper fitting procedures each time you wear the respirator. When in doubt review the user seal check instructions. If a proper fit cannot be achieved, do not enter the area requiring respiratory protection. Follow up with your supervisor.
Keep in mind that when you are wearing a respirator, it helps reduce potential exposures if the respirator fits you properly, you wear it during all times of exposure and use of the respirator is under an effective respiratory protection program as required by OSHA 29 CFR 1910.134.
Refer to the OSHA website at www.OSHA.gov for the most current information about use of respirators.
Contact your 3M Sales Representative or call the 3M Health Care Customer Helpline for information on personal protective equipment, including the respirators described in this training, and to learn more about the other elements of a respiratory protection program.
By Charlotte from Tunisia - 2015.02.21 12:14
A nice supplier in this industry, after a detail and careful discussion, we reached a consensus agreement. Hope that we cooperate smoothly.
By Bertha from Benin - 2016.08.15 12:36